Plumbing 101: A Necessity for Installing a Bathtub
Plumbing 101: A Necessity for Installing a Bathtub
Blog Article
We've encountered the article involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the web and figured it made good sense to write about it with you in this article.
Setting up a bathtub isn't precisely brain surgery, yet it does require strong plumbing, carpentry, and also often, tiling abilities. Changing an old tub with a new one is also a reasonably hard job. If the old bathtub is easily available, the task can move speedily; if you need to open a wall to eliminate the old tub and also place the brand-new bathtub, the job is a lot harder. In either situation, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. Ensure you have actually certified on your own for the work and are comfortable attempting it. As opposed to working with a professional to take over a halfway-completed job, it is far better to consider employing one before you begin. Possibilities are you may need a professional plumber to make tube connections.
This short article will certainly assist you install a new bathtub in your restroom if you have currently gotten a brand-new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your devices and product checklist should consist of the following:
Getting ready for the Setup
Firstly, the sustaining framework supplied with the bath must be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps system to stop stress on the bath tub.
Fit the adaptable tap ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final placement.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is disconnect the water supply. After doing so, activate the faucets to drain any water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome because of the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Before going on to fit the brand-new taps, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bathtub
Making use of both wooden boards under its feet, place the bathtub in the needed setting. The wood boards are helpful in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the tub up until the spirit level reviews degree.
To install taps, fit all-time low of the furthest flexible faucet connector to the appropriate supply pipeline by making a compression join; after that do the exact same for the other faucet.
Switch on the water system and examine all joints as well as new pipework for leaks and also tighten them if necessary. Fill up the bath tub and likewise inspect the overflow outlet and also the normal outlet for leaks.
Lastly, fix the bath paneling as defined in the supplier's instruction manual. Tiling and sealing around the bathtub needs to wait up until the tub has actually been used at the very least when as this will resolve it into its last position.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end provides a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making sure that the washers remain in location between the faucet and also the sink. Secure the faucet in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet adapters. The former type must be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack an inflexible seal, creating the water to penetrate the wall surface in between the bathroom as well as the tiling, causing problems with dampness and possible leaks to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, and can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to always load the bathtub with water before sealing, to permit the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily readily available on the marketplace. It is a good idea to fit the ceramic tiles using waterproof or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that review about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the web. Enjoyed reading our article? Please share it. Let other people find it. I cherish reading our article about Installing A Bathtub.
Your search ends; experts here. Report this page